We use Air rifles to provide a free solution for the on-going control of common* farm pests. For more info about us and the service we provide contct us via Email. *Rabbits, Rats and pest species of birds (see WCA1981)
Wednesday, July 30, 2008
New ballistol products
Saturday, July 26, 2008
What i have been up to.
We had a walk round as mike had started to build the first of 4 permanent hides and also to see how the rabbit population was doing.
I also took some pics of the B+B rooms that are now open at the farm (more on them later)
The one thing we found whilst walking out of the yard was a large grass snake. I didn't get a photo of it because mike scared it off before i got a chance, you see, he ain't to fond of snakes and as you can imagine he was more than startled to see a two foot long snake just six inches away from his boot.
This rat made the mistake of trying to eat at my bird table. It was jumping up onto a low level feeding bowl ,full of crushed peanuts and bird seed when I spotted him. He was very bold and didn't seem to flinch one bit as i looked at him sitting there eating my bird food. But he stopped dead in his tracks when I hit him in the head with a bisley super field, that was his last supper.
Surprisingly I haven't seen any more rats coming to the table for some time but i am sure they will be back , and give me some moving target practice.
Oh and not forgetting the rabbit i shot when i went to the farm. I hit this one in the head, just above the eye, at 65 yards. One shot One kill. I was on form and won the respect of the land owner who was almost certain i had missed, but when he stopped moving and i walked towards him he didn't run the farmer soon changed his mind to "dam fine shooting here Richard, well done".
Saturday, July 12, 2008
Ballistol links
Use the comments link at the bottom of this post to let me know what you think and i will pass the feedback onto Ballistol.
Thanks
Richard
Saturday, July 5, 2008
zeroing your scope
Zeroing a sight or scope means getting the crosshair in position so that when you shoot. Ground zero if you like. The point of impact.There's a lot of discussion amongst shooters on the best way to zero a scope or sight. What I've written below is what I've been sending out to my ebay scope buyers for the last year or so and received a lot of good comments back about it so I know it's OK!
How to Zero a Rifle Scope
First of all you need to set a firm foundation by fitting the scope mounts well.
Put the scope mounts on the rifle first with the top brackets removed.
Tighten them into place using 1/2 turns at the time so that they sit solid and level as best as is possible, i.e., the downward pressure is as equal as possible. At this stage don't tighten them fully as you might want to slide them up and down a little.
Now take scope and place it on top of the open rifle mounts.
Make sure the windage and elevation turrets are one up and one to the right (these are the "turrets" on the sight. You use them later to make micro adjustments and in the field adjustments for wind)
Then put the top mount brackets on and tighten - Again use partial turns to tighten up.
Don't tighten fully at this stage, you may yet need to adjust a little.
Zero the scope
Lie in your normal shooting position and check that you can see through the scope well...
The distance between your eye and the rear scope lens is called Eye Relief.
Unlike cartoons you do not use a scope by pressing your eye up against the scope lens!
Once comfortable complete the screwing down of all mounts so that your set up is solid -
take care at this stage to keep the final turns partial and one by one to ensure pressure is equal.
Now it's time to zero the scope for shooting:
Load the rifle
Adopt your standard prone/lie down shooting position.
Prone is the best way as if you test shoot from standing or kneeling positions you waver more and it's harder to do a "true test".
Put some sort of target in place at 30 yards - this is a "standard" range .
Using cross hair on target centre - Take 2-3 shots - Where do do they fall in relation to where you want them to? Right, left, up, down - dead on . Take 5 more shots as this will average out shooter inaccuracy and give you a more "significant" feel for how far or close you are from true zero.
Now it's time to use the windage and elevation turrets to get it zeroed dead on. These are the 2 turrets on the top and right side of the scope. Models vary, you'll probably screw a cap off and expose either a coin twist or finger knurled type of dial.
The top turret adjusts up and down.
If you have your scopes instructions they should have a table with figures to tell you what each click adjustment means in terms of cross hair movement at "x" distance, e.g., 1/8 inch at 100 metres. Use single click turns and each time take a new shot to gauge where the shot now falls - the dials basically adjust the cross hair position up-down and left-right.
It's trial and error basically but with testing you'll get to where you need to be and be able to trust that your shots will go where it says they will! This may take some time and a lot of shots. Be patient!